CubieBoard中文论坛

 找回密码
 立即注册
搜索
热搜: unable
楼主: matson

cb2/ct的debian固件 - debieez

[复制链接]
发表于 2013-12-25 23:46:55 | 显示全部楼层
Good job, 繼續努力!
回复 支持 反对

使用道具 举报

发表于 2013-12-26 04:48:51 | 显示全部楼层
本帖最后由 Ahrovan 于 2013-12-26 04:49 编辑

CUBIEez installed in nand & i can not use network for connect to internet or use apt-get install command - driver is not ported ? or i can set or config that ?? thansk
回复 支持 反对

使用道具 举报

 楼主| 发表于 2013-12-26 12:42:47 | 显示全部楼层
Ahrovan 发表于 2013-12-26 04:48
CUBIEez installed in nand & i can not use network for connect to internet or use apt-get install com ...

cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet should work
回复 支持 反对

使用道具 举报

发表于 2013-12-26 18:01:50 | 显示全部楼层
matson 发表于 2013-12-26 12:42
cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet s ...
CB2{-A20}
///
cubie@cubieez:~$ sudo su
[sudo] password for cubie:
root@cubieez:/home/cubie# ifconfig
eth0      Link encap:Ethernet  HWaddr 02:07:08:02:85:00  
          inet addr:192.168.1.124  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:320 (320.0 B)  TX bytes:0 (0.0 B)
          Interrupt:87 Base address:0x4000

lo        Link encapocal Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:64 errors:0 dropped:0 overruns:0 frame:0
          TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5184 (5.0 KiB)  TX bytes:5184 (5.0 KiB)

root@cubieez:/home/cubie#
///
eth0 net device is ok,but i can not use internet with browser or command apt-get,is ip true? or not
thanks!
回复 支持 反对

使用道具 举报

发表于 2013-12-26 18:38:06 | 显示全部楼层
matson 发表于 2013-12-26 12:42
cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet s ...

sunxi-gpio kernel module ::
can we use sunxi-gpio module in cubieez - this module ported into cubieez kernel ?
ex:
$ echo 1 > /sys/class/gpio/export
  $ echo 2 > /sys/class/gpio/export
  $ echo 3 > /sys/class/gpio/export
& can we use http://docs.cubieboard.org/tutor ... g_and_configuration
for cubieez ?
thanks !
回复 支持 反对

使用道具 举报

 楼主| 发表于 2013-12-26 20:34:27 | 显示全部楼层
Ahrovan 发表于 2013-12-26 18:01
CB2{-A20}
///
cubie@cubieez:~$ sudo su

192.168.1.124 is set statictly, I think you need to change the /etc/network/interface config file, or just run the following command:
sudo dhclient eth0
回复 支持 反对

使用道具 举报

发表于 2013-12-26 20:35:46 | 显示全部楼层
擦,怎么ct 刷这个系统,我的 rapoo 8100 无线键盘不能用了。。。
usb 接收器上的小灯我按键时有反应啊~~
原来 lubuntu 下是可以用的~~

为什么~~
回复 支持 反对

使用道具 举报

 楼主| 发表于 2013-12-26 20:36:14 | 显示全部楼层
Ahrovan 发表于 2013-12-26 18:38
sunxi-gpio kernel module ::
can we use sunxi-gpio module in cubieez - this module ported into cu ...

already builtin gpio_sunxi module
回复 支持 反对

使用道具 举报

 楼主| 发表于 2013-12-26 20:37:29 | 显示全部楼层
CJH_cubietech 发表于 2013-12-26 20:35
擦,怎么ct 刷这个系统,我的 rapoo 8100 无线键盘不能用了。。。
usb 接收器上的小灯我按键时有反应啊~~:d ...

驱动太多了,所以去掉了一些。估计一个不小心把你要的那个驱动干掉了
回复 支持 反对

使用道具 举报

发表于 2013-12-26 20:44:21 | 显示全部楼层
matson 发表于 2013-12-26 20:37
驱动太多了,所以去掉了一些。估计一个不小心把你要的那个驱动干掉了

意思就是我的键盘就不能用了??
我还有个rapoo 1800.pro 的无线键盘倒是能用,
有没有什么办法补救??
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|Archiver|手机版|粤ICP备13051116号|cubie.cc---深刻的嵌入式技术讨论社区

GMT+8, 2024-3-19 17:18 , Processed in 0.022643 second(s), 13 queries .

Powered by Discuz! X3.4

© 2001-2012 Comsenz Inc. | Style by Coxxs

返回顶部