设为首页CubieBoard博客-HomeCubieTech公司网站收藏本站
切换到宽版

CubieBoard中文论坛

 找回密码
 立即注册
搜索
热搜: unable
CubieBoard中文论坛»论坛 › 发行版汇 › OpenWRT › Cubieboard安装Openwrt教程 (可以不需要编译) ...
返回列表 发新帖
查看: 35025|回复: 9

Cubieboard安装Openwrt教程 (可以不需要编译)

[复制链接]
tll
发表于 2013-6-16 18:44:18 | 显示全部楼层 |阅读模式
本帖最后由 tll 于 2013-6-21 23:47 编辑

感谢hipboi，本帖子在Ubuntu 12.04.1 （Mac）下写

A 直接用img弄，但是这样分区大小固定
img我用的是512的卡导出的，下次给
B 用fdisk分区，分区大小为最大
其中分两个，一种不编译，下载编译好的，一种自己编译
这里讲不需要编译的
先下载东西：
  1. wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/openwrt-sunxi-cubie-rootfs.tar.gz
  2. #下载rootfs
  3. wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/script.bin
  4. #下载script.bin配置文件
  5. wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/sunxi-spl.bin
  6. wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/u-boot.bin
  7. #下载uboot
  8. wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/openwrt-sunxi-uImage
  9. #下载uimage
复制代码
然后呢，插入SD卡（读卡器），使用dmesg命令看下SD卡是哪个文件，我就因为弄错文件而把我的本地磁盘格式化了……幸亏找回了数据
我这里以/dev/sdb为例开始
Ubuntu会自动挂上插入的磁盘，所以我们需要去掉挂载（假设我的SD上有两个分区）
  1. umount /dev/sdb1
  2. umount /dev/sdb2
复制代码
然后开始分区咯，先用fdisk -l记录下磁盘的数据（这是我另一个卡，只有32M，给大家做演示的）
  1. Disk /dev/sdb: 32 MB, 32112640 bytes
  2. 2 heads, 32 sectors/track, 980 cylinders, total 62720 sectors
  3. Units = sectors of 1 * 512 = 512 bytes
  4. Sector size (logical/physical): 512 bytes / 512 bytes
  5. I/O size (minimum/optimal): 512 bytes / 512 bytes
  6. Disk identifier: 0x00000000

  8.    Device Boot      Start         End      Blocks   Id  System
复制代码
由上可知，1 sector是512字节，即2 sectors就是1kb了，总共有62740个（不同卡可能不同）
再输入 fdisk /dev/sdb，然后输入d 1，再输入 d 2，删除分区（这个不太确定命令是否正确）。
然后开始做第一个分区
要做第一个分区，我们可以使用berryboot的img文件，将他导入进卡即可，这里先不讲。
又或者，你可以继续用fdisk来执行操作，输入n，然后分区号，开始的值都是默认，下面的最后一个sector，我第一个分区需要32M，则
2（2sectors=1k）*1024（1024k=1m）*32（32M）+2048（加上开始的部分）=67584，比我的总数还大，这是因为32M的卡本身就没32M
然后再使用n命令一次，这次全部用默认值，最后用w命令写入。
格式化：
  1. mkfs.vfat /dev/sdb1
  2. mkfs.ext4 /dev/sdb2
复制代码
然后呢，新建文件夹/temp
  1. mkdir /temp
复制代码
挂上1到/temp，复制文件，去掉，又上2，解压rootfs
  1. mount /dev/sdb1 /temp
  2. cp openwrt-sunxi-uImage /mnt/temp/uImage
  3. cp script.bin /mnt/temp/
  4. umount /mnt/temp
  5. mount /dev/sdb2 /temp
  6. cp openwrt-sunxi-cubie-rootfs.tar.gz /tmp
  7. cd /mnt/temp
  8. <pre>tar -zxvf /tmp/openwrt-sunxi-cubie-rootfs.tar.gz
  9. cd
  10. umount /mnt/temp
  11. </pre>
复制代码
OK~
该写入uboot了，执行：
  1. dd if=sunxi-spl.bin of=/dev/sdb bs=1024 seek=8
  2. dd if=u-boot.bin of=/dev/sdb bs=1024 seek=32
复制代码
接下来插上TTL，然后给cb放上SD卡（两个都是必需要做），在终端里安装screen：
  1. apt-get install screen -y
复制代码
接着启动：
  1. screen /dev/ttyUSB0 115200
复制代码
此时终端变空了，插上电源，在3秒倒数是按下任意按钮进入uboot命令行，输入：
  1. setenv setargs setenv bootargs console=${console} root=${root} loglevel=${loglevel} ${panicarg} ${extraargs} init=/etc/preinit

  3. saveenv
复制代码
原因：openwrt要先启动preinit而不是直接启动init
好了，使用boot命令启动吧~

最后附上启动出现的字：
  1. U-Boot SPL 2012.10-04280-g1a8ac55 (May 25 2013 - 19:42:12)
  2. DRAM: 1024MB
  3. SUNXI SD/MMC: 0


  6. U-Boot 2012.10-04280-g1a8ac55 (May 25 2013 - 19:42:12) Allwinner Technology

  8. CPU:   SUNXI Family
  9. Board: Cubieboard
  10. I2C:   ready
  11. DRAM:  1 GiB
  12. MMC:   SUNXI SD/MMC: 0
  13. In:    serial
  14. Out:   serial
  15. Err:   serial
  16. Hit any key to stop autoboot:  0
  17. reading uEnv.txt

  19. ** Unable to read "uEnv.txt" from mmc 0:1 **
  20. Loading file "uEnv.txt" from mmc device 0:1
  21. Failed to mount ext2 filesystem...
  22. ** Bad ext2 partition or disk - mmc 0:1 **
  23. ext2load - load binary file from a Ext2 filesystem

  25. Usage:
  26. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  27.     - load binary file 'filename' from 'dev' on 'interface'
  28.       to address 'addr' from ext2 filesystem
  29. Loading file "boot/uEnv.txt" from mmc device 0:1
  30. Failed to mount ext2 filesystem...
  31. ** Bad ext2 partition or disk - mmc 0:1 **
  32. ext2load - load binary file from a Ext2 filesystem

  34. Usage:
  35. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  36.     - load binary file 'filename' from 'dev' on 'interface'
  37.       to address 'addr' from ext2 filesystem
  38. reading boot.scr

  40. ** Unable to read "boot.scr" from mmc 0:1 **
  41. Loading file "boot.scr" from mmc device 0:1
  42. Failed to mount ext2 filesystem...
  43. ** Bad ext2 partition or disk - mmc 0:1 **
  44. ext2load - load binary file from a Ext2 filesystem

  46. Usage:
  47. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  48.     - load binary file 'filename' from 'dev' on 'interface'
  49.       to address 'addr' from ext2 filesystem
  50. Loading file "boot/boot.scr" from mmc device 0:1
  51. Failed to mount ext2 filesystem...
  52. ** Bad ext2 partition or disk - mmc 0:1 **
  53. ext2load - load binary file from a Ext2 filesystem

  55. Usage:
  56. ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
  57.     - load binary file 'filename' from 'dev' on 'interface'
  58.       to address 'addr' from ext2 filesystem
  59. reading script.bin

  61. 43628 bytes read
  62. reading uImage

  64. 3410200 bytes read
  65. ## Booting kernel from Legacy Image at 48000000 ...
  66.    Image Name:   Linux-3.4.43
  67.    Image Type:   ARM Linux Kernel Image (uncompressed)
  68.    Data Size:    3410136 Bytes = 3.3 MiB
  69.    Load Address: 40008000
  70.    Entry Point:  40008000
  71.    Verifying Checksum ... OK
  72.    Loading Kernel Image ... OK
  73. OK

  75. Starting kernel ...

  77. [    0.000000] Booting Linux on physical CPU 0
  78. [    0.000000] Linux version 3.4.43 (saverio@nockid) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36556) ) #1 PREEMPT Sat May 25 19:11:24 CEST 2013
  79. [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
  80. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  81. [    0.000000] Machine: sun4i
  82. [    0.000000] Memory Reserved:
  83. [    0.000000]         SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
  84. [    0.000000]         VE   : 0x44000000 - 0x48ffffff  (  80 MB)
  85. [    0.000000]         G2D  : 0x49000000 - 0x49ffffff  (  16 MB)
  86. [    0.000000] Memory policy: ECC disabled, Data cache writeback
  87. [    0.000000] chip-id: A10 (AW1623 revision C)
  88. [    0.000000] On node 0 totalpages: 262144
  89. [    0.000000] free_area_init_node: node 0, pgdat c0669974, node_mem_map c0710000
  90. [    0.000000]   Normal zone: 1520 pages used for memmap
  91. [    0.000000]   Normal zone: 0 pages reserved
  92. [    0.000000]   Normal zone: 193040 pages, LIFO batch:31
  93. [    0.000000]   HighMem zone: 528 pages used for memmap
  94. [    0.000000]   HighMem zone: 67056 pages, LIFO batch:15
  95. [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  96. [    0.000000] pcpu-alloc: [0] 0
  97. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
  98. [    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 init=/etc/preinit
  99. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  100. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  101. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  102. [    0.000000] Memory: 1024MB = 1024MB total
  103. [    0.000000] Memory: 933936k/933936k available, 114640k reserved, 270336K highmem
  104. [    0.000000] Virtual kernel memory layout:
  105. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  106. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  107. [    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
  108. [    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
  109. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  110. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  111. [    0.000000]       .text : 0xc0008000 - 0xc0600000   (6112 kB)
  112. [    0.000000]       .init : 0xc0600000 - 0xc062a000   ( 168 kB)
  113. [    0.000000]       .data : 0xc062a000 - 0xc0672d98   ( 292 kB)
  114. [    0.000000]        .bss : 0xc0672dbc - 0xc070f220   ( 626 kB)
  115. [    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  116. [    0.000000] NR_IRQS:128
  117. [    0.000000] timer0: Periodic Mode
  118. [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
  119. [    0.000000] Console: colour dummy device 80x30
  120. [    0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
  121. [    0.050000] pid_max: default: 32768 minimum: 301
  122. [    0.050000] Mount-cache hash table entries: 512
  123. [    0.050000] CPU: Testing write buffer coherency: ok
  124. [    0.050000] Setting up static identity map for 0x4044dc10 - 0x4044dc68
  125. [    0.050000] devtmpfs: initialized
  126. [    0.050000] dummy:
  127. [    0.050000] NET: Registered protocol family 16
  128. [    0.050000] Init eGon pin module V2.0
  129. [    0.050000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
  130. [    0.050000] Initialize DMAC OK
  131. [    0.050000] bio: create slab <bio-0> at 0
  132. [    0.050000] SCSI subsystem initialized
  133. [    0.050000] libata version 3.00 loaded.
  134. [    0.050000] usbcore: registered new interface driver usbfs
  135. [    0.050000] usbcore: registered new interface driver hub
  136. [    0.050000] usbcore: registered new device driver usb
  137. [    0.050000] Linux video capture interface: v2.00
  138. [    0.050000] Advanced Linux Sound Architecture Driver Version 1.0.25.
  139. [    0.050000] Bluetooth: Core ver 2.16
  140. [    0.060000] NET: Registered protocol family 31
  141. [    0.060000] Bluetooth: HCI device and connection manager initialized
  142. [    0.060000] Bluetooth: HCI socket layer initialized
  143. [    0.060000] Bluetooth: L2CAP socket layer initialized
  144. [    0.060000] Bluetooth: SCO socket layer initialized
  145. [    0.060000] cfg80211: Calling CRDA to update world regulatory domain
  146. [    0.060000] Switching to clocksource aw 64bits couter
  147. [    0.060000] FS-Cache: Loaded
  148. [    0.060000] CacheFiles: Loaded
  149. [    0.090000] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
  150. [    0.090000] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
  151. [    0.090000] hub 1-0:1.0: USB hub found
  152. [    0.090000] hub 1-0:1.0: 1 port detected
  153. [    0.090000] NET: Registered protocol family 2
  154. [    0.090000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  155. [    0.090000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  156. [    0.100000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
  157. [    0.100000] TCP: Hash tables configured (established 131072 bind 65536)
  158. [    0.100000] TCP: reno registered
  159. [    0.100000] UDP hash table entries: 512 (order: 1, 8192 bytes)
  160. [    0.100000] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
  161. [    0.100000] NET: Registered protocol family 1
  162. [    0.100000] audit: initializing netlink socket (disabled)
  163. [    0.100000] type=2000 audit(0.099:1): initialized
  164. [    0.100000] highmem bounce pool size: 64 pages
  165. [    0.110000] VFS: Disk quotas dquot_6.5.2
  166. [    0.110000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  167. [    0.120000] fuse init (API version 7.18)
  168. [    0.120000] msgmni has been set to 1296
  169. [    0.120000] alg: No test for stdrng (krng)
  170. [    0.120000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
  171. [    0.120000] io scheduler noop registered
  172. [    0.120000] io scheduler deadline registered
  173. [    0.120000] io scheduler cfq registered (default)
  174. [    0.120000] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
  175. [    0.130000] [uart]: used uart info.: 0x05
  176. [    0.130000] [uart]: serial probe 0 irq 1 mapbase 0x01c28000
  177. [    0.150000] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
  178. [    0.680000] console [ttyS0] enabled
  179. [    0.680000] [uart]: serial probe 2 irq 3 mapbase 0x01c28800
  180. [    0.710000] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A
  181. [    0.720000] G2D: drv_g2d_init
  182. [    0.720000] G2D: g2dmem: g2d_start=49000000, g2d_size=1000000
  183. [    0.730000] G2D: head:c9000000,tail:ca000000
  184. [    0.730000] G2D: Module initialized.major:252
  185. [    0.740000] brd: module loaded
  186. [    0.740000] loop: module loaded
  187. [    0.750000] [NAND]nand driver, init.
  188. [    0.750000] cmu_clk is 480
  189. [    0.750000] nand clk init end
  190. [    0.760000] offset 0xc:  0x6141
  191. [    0.760000] offset 0x14:  0x8200000b
  192. [    0.760000] [NAND] nand gpio_request
  193. [    0.770000] [NAND] nand driver version: 0x2 0x9
  194. [    0.770000] nand interrupte register ok
  195. [    0.780000] ret of NFC_ChangMode is 0
  196. [    0.780000] dma_hdle  is 0
  197. [    0.780000] dma_hdle  is 10000008
  198. [    0.790000] cmu_clk is 480
  199. [    0.790000] nand clk init end
  200. [    0.790000] offset 0xc:  0x6141
  201. [    0.800000] offset 0x14:  0x82000007
  202. [    0.860000] Dev nand: part 1, start 2048, size 131072
  203. [    0.860000] Dev nand: part 2, start 133120, size 4096
  204. [    0.870000] Dev nand: part 3, start 137216, size 2097152
  205. [    0.870000] Dev nand: part 4, start 2234368, size 2097152
  206. [    0.880000] Dev nand: part 5, start 4331520, size 2097152
  207. [    0.880000] Dev nand: part 6, start 6428672, size 1048576
  208. [    0.890000] Dev nand: part 7, start 7477248, size 501760
  209. [    0.890000]  nand: nanda nandb nandc nandd nande nandf nandg
  210. [    0.900000] benn: nand probe enter
  211. [    0.910000] [NAND]nand driver, ok.
  212. [    0.910000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  213. [    0.920000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  214. [    0.920000] [sw-ehci1]: open clock
  215. [    0.950000] [sw-ehci1]: Set USB Power ON
  216. [    0.950000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  217. [    0.960000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
  218. [    0.960000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
  219. [    0.990000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
  220. [    0.990000] hub 2-0:1.0: USB hub found
  221. [    1.000000] hub 2-0:1.0: 1 port detected
  222. [    1.000000] [sw-ohci1]: open clock
  223. [    1.020000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  224. [    1.030000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
  225. [    1.040000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
  226. [    1.100000] hub 3-0:1.0: USB hub found
  227. [    1.100000] hub 3-0:1.0: 1 port detected
  228. [    1.110000] [sw-ehci2]: open clock
  229. [    1.130000] [sw-ehci2]: Set USB Power ON
  230. [    1.140000] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  231. [    1.140000] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
  232. [    1.150000] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
  233. [    1.180000] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
  234. [    1.180000] hub 4-0:1.0: USB hub found
  235. [    1.190000] hub 4-0:1.0: 1 port detected
  236. [    1.190000] [sw-ohci2]: open clock
  237. [    1.210000] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
  238. [    1.220000] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
  239. [    1.230000] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
  240. [    1.290000] hub 5-0:1.0: USB hub found
  241. [    1.290000] hub 5-0:1.0: 1 port detected
  242. [    1.300000] mousedev: PS/2 mouse device common for all mice
  243. [    1.300000] sunxi RTC version 0.1
  244. [    1.310000] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380248073
  245. [    1.310000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
  246. [    1.320000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
  247. [    1.330000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
  248. [    1.330000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
  249. [    1.340000] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
  250. [    1.340000] i2c /dev entries driver
  251. [    1.350000] lirc_dev: IR Remote Control driver registered, major 251
  252. [    1.350000] IR NEC protocol handler initialized
  253. [    1.360000] IR RC5(x) protocol handler initialized
  254. [    1.360000] IR RC6 protocol handler initialized
  255. [    1.370000] IR JVC protocol handler initialized
  256. [    1.370000] IR Sony protocol handler initialized
  257. [    1.380000] IR RC5 (streamzap) protocol handler initialized
  258. [    1.380000] IR SANYO protocol handler initialized
  259. [    1.390000] IR MCE Keyboard/mouse protocol handler initialized
  260. [    1.390000] IR LIRC bridge handler initialized
  261. [    1.400000] [cedar dev]: install start!!!
  262. [    1.400000] [cedar dev]: install end!!!
  263. [    1.400000] [ace_drv] start!!!
  264. [    1.410000] [ace_drv] init end!!!
  265. [    1.410000] [pa_drv] start!!!
  266. [    1.410000] [pa_drv] init end!!!
  267. [    1.420000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  268. [    1.430000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  269. [    1.430000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  270. [    1.440000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  271. [    1.450000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  272. [    1.460000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  273. [    1.470000] Bluetooth: HCI UART driver ver 2.2
  274. [    1.470000] Bluetooth: HCI H4 protocol initialized
  275. [    1.480000] Bluetooth: HCI BCSP protocol initialized
  276. [    1.480000] Bluetooth: HCILL protocol initialized
  277. [    1.480000] cpuidle: using governor ladder
  278. [    1.490000] cpuidle: using governor menu
  279. [    1.490000] [mmc_pm]: no sdio card used in configuration
  280. [    1.500000] [mmc]: sunximmc_init
  281. [    1.500000] [mmc]: sunxi mmc controller using config : 0xb
  282. [    1.510000] [mmc]: sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
  283. [    1.510000] [mmc]: mmc 0 power off !!
  284. [    1.520000] [mmc]: mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xef394000, ret 0.
  285. [    1.530000] [mmc]: sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
  286. [    1.530000] [mmc]: mmc 1 power off !!
  287. [    1.540000] [mmc]: mmc1 Probe: base:0xf1c10000 irq:33 dma:0 pdes:0xef398000, ret 0.
  288. [    1.550000] [mmc]: sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
  289. [    1.550000] [mmc]: mmc 3 power off !!
  290. [    1.560000] [mmc]: mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xef39c000, ret 0.
  291. [    1.570000] IPv4 over IPv4 tunneling driver
  292. [    1.570000] TCP: cubic registered
  293. [    1.570000] Initializing XFRM netlink socket
  294. [    1.580000] NET: Registered protocol family 10
  295. [    1.590000] IPv6 over IPv4 tunneling driver
  296. [    1.590000] NET: Registered protocol family 17
  297. [    1.600000] NET: Registered protocol family 15
  298. [    1.600000] Bluetooth: RFCOMM TTY layer initialized
  299. [    1.610000] Bluetooth: RFCOMM socket layer initialized
  300. [    1.610000] Bluetooth: RFCOMM ver 1.11
  301. [    1.620000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  302. [    1.620000] Bluetooth: BNEP filters: protocol multicast
  303. [    1.630000] 8021q: 802.1Q VLAN Support v1.8
  304. [    1.630000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
  305. [    1.640000] Registering SWP/SWPB emulation handler
  306. [    1.640000] registered taskstats version 1
  307. [    1.650000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  308. [    1.660000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  309. [    1.660000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  310. [    1.670000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  311. [    1.680000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  312. [    1.690000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  313. [    1.690000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
  314. [    1.700000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
  315. [    1.710000] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:04:16 UTC (1262304256)
  316. [    1.710000] ALSA device list:
  317. [    1.720000]   No soundcards found.
  318. [    1.720000] Waiting for root device /dev/mmcblk0p2...
  319. [    2.520000] [mmc]: mmc 0 detect change, present 1
  320. [    2.820000] [mmc]: mmc 0 power on !!
  321. [    2.860000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 52,  RTO !!
  322. [    2.860000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 52,  RTO !!
  323. [    2.870000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 8,  RTO !!
  324. [    2.880000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 5,  RTO !!
  325. [    2.890000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 5,  RTO !!
  326. [    2.900000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 5,  RTO !!
  327. [    2.900000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 5,  RTO !!
  328. [    2.920000] [mmc]: sdxc_request_done(L1114): smc 0 err, cmd 8,  RTO !!
  329. [    2.940000] mmc0: new high speed SD card at address 0260
  330. [    2.950000] mmcblk0: mmc0:0260 NCard 481 MiB
  331. [    2.960000]  mmcblk0: p1 p2
  332. [    2.960000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
  333. [    2.970000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
  334. [    2.980000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  335. [    2.980000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  336. [    2.990000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  337. [    3.000000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  338. [    3.050000] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
  339. [    3.060000] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
  340. [    3.080000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
  341. [    3.090000] VFS: Mounted root (ext4 filesystem) on device 179:2.
  342. [    3.100000] devtmpfs: mounted
  343. [    3.100000] Freeing init memory: 168K
  344. probing /dev/mmcblk0 for uboot env data
  345. Detected generic sunxi // generic sunxi
  346. - preinit -
  347. Press the [f] key and hit [enter] to enter failsafe mode
  348. - regular preinit -
  349. [    9.270000] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
  350. - init -

  352. Please press Enter to activate this console. [   10.500000] !!! base_Addr = 0xf1c2ac00
  353. [   10.510000] config i2c gpio with gpio_config api
  354. [   10.510000] twi0, apb clock = 24000000
  355. [   10.530000] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
  356. [   10.550000] axp20_ldo1: 1300 mV
  357. [   10.570000] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
  358. [   10.600000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  359. [   10.600000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  360. [   10.620000] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
  361. [   10.640000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
  362. [   10.640000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
  363. [   10.680000] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
  364. [   10.740000] axp20_ldo2: Failed to create debugfs directory
  365. [   10.740000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  366. [   10.820000] axp20_buck2: 700 <--> 2275 mV at 1400 mV
  367. [   10.820000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
  368. [   10.900000] axp20_buck3: 700 <--> 3500 mV at 1250 mV
  369. [   10.970000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
  370. [   10.990000] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
  371. [   11.080000] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.41/input/input0
  372. [   11.380000] I2C: i2c-0: AW16XX I2C adapter
  373. [   11.490000] !!! base_Addr = 0xf1c2b000
  374. [   11.490000] twi1, apb clock = 24000000
  375. [   11.580000] I2C: i2c-1: AW16XX I2C adapter
  376. [   11.650000] !!! base_Addr = 0xf1c2b400
  377. [   11.650000] twi2, apb clock = 24000000
  378. [   11.760000] I2C: i2c-2: AW16XX I2C adapter
  379. [   11.930000] enter sun4i Audio codec!!!
  380. [   11.930000] sun4i audio support initialized
  381. [   11.940000] sun4i Audio codec successfully loaded..
  382. [   11.960000] input: sun4i-ir as /devices/virtual/input/input1
  383. [   11.960000] IR Initial OK
  384. [   11.970000] wemac Ethernet Driver, V1.01 in file:drivers/net/ethernet/sun4i/sun4i_wemac.c
  385. [   11.980000] [EMAC] ahb clk enable
  386. [   11.980000] [EMAC] ahb gate clk: 0x2615f
  387. [   12.030000] emac MAC isn't valid!
  388. [   12.040000] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
  389. [   12.050000] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
  390. [   12.060000] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
  391. [   12.070000] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
  392. [   12.070000] scsi0 : sw_ahci_platform
  393. [   12.080000] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 56
  394. [   12.440000] ata1: SATA link down (SStatus 0 SControl 300)
  395. [   12.480000] PPP generic driver version 2.4.2
  396. [   12.500000] tun: Universal TUN/TAP device driver, 1.6
  397. [   12.500000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  398. [   12.540000] ip_tables: (C) 2000-2006 Netfilter Core Team
  399. [   12.600000] xt_time: kernel timezone is -0000
  400. [   12.630000] nf_conntrack version 0.5.0 (14595 buckets, 58380 max)
  401. [   12.730000] usbcore: registered new interface driver cdc_acm
  402. [   12.740000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  403. [   12.760000] usbcore: registered new interface driver usbserial
  404. [   12.770000] usbcore: registered new interface driver usbserial_generic
  405. [   12.780000] USB Serial support registered for generic
  406. [   12.780000] usbserial: USB Serial Driver core
  407. [   12.800000] Initializing USB Mass Storage driver...
  408. [   12.810000] usbcore: registered new interface driver usb-storage
  409. [   12.810000] USB Mass Storage support registered.
  410. [   12.820000] usbcore: registered new interface driver cdc_ncm
  411. [   12.850000] usbcore: registered new interface driver option
  412. [   12.860000] USB Serial support registered for GSM modem (1-port)
  413. [   12.900000] usbcore: registered new interface driver uvcvideo
  414. [   12.900000] USB Video Class driver (1.1.1)
  415. [   16.030000] wemac wemac.0: WARNING: no IRQ resource flags set.
  416. [   16.140000] wemac wemac.0: eth0: link down
  417. [   16.140000] ADDRCONF(NETDEV_UP): eth0: link is not ready
  418. [   16.210000] device eth0 entered promiscuous mode
  419. [   16.210000] ADDRCONF(NETDEV_UP): br-lan: link is not ready



  423. BusyBox v1.19.4 (2013-05-25 19:11:40 CEST) built-in shell (ash)
  424. Enter 'help' for a list of built-in commands.

  426.   _______                     ________        __
  427. |       |.-----.-----.-----.|  |  |  |.----.|  |_
  428. |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  429. |_______||   __|_____|__|__||________||__|  |____|
  430.           |__| W I R E L E S S   F R E E D O M
  431. -----------------------------------------------------
  432. BARRIER BREAKER (Bleeding Edge, r36713)
  433. -----------------------------------------------------
  434.   * 1/2 oz Galliano         Pour all ingredients into
  435.   * 4 oz cold Coffee        an irish coffee mug filled
  436.   * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  437.   * 2 tsp. Creme de Cacao
  438. -----------------------------------------------------
  439. root@OpenWrt:/#
复制代码
Busybox：
  1. root@OpenWrt:/# busybox
  2. BusyBox v1.19.4 (2013-05-25 19:11:40 CEST) multi-call binary.
  3. Copyright (C) 1998-2011 Erik Andersen, Rob Landley, Denys Vlasenko
  4. and others. Licensed under GPLv2.
  5. See source distribution for full notice.

  7. Usage: busybox [function] [arguments]...
  8.    or: busybox --list[-full]
  9.    or: function [arguments]...

  11.         BusyBox is a multi-call binary that combines many common Unix
  12.         utilities into a single executable.  Most people will create a
  13.         link to busybox for each function they wish to use and BusyBox
  14.         will act like whatever it was invoked as.

  16. Currently defined functions:
  17.         [, [[, arping, ash, awk, basename, brctl, bunzip2, bzcat, cat, chgrp,
  18.         chmod, chown, chroot, clear, cmp, cp, crond, crontab, cut, date, dd,
  19.         df, dirname, dmesg, du, echo, egrep, env, expr, false, fgrep, find,
  20.         free, fsync, grep, gunzip, gzip, halt, head, hexdump, hostid, hwclock,
  21.         id, ifconfig, init, insmod, kill, killall, klogd, less, ln, lock,
  22.         logger, logread, ls, lsmod, md5sum, mkdir, mkfifo, mknod, mkswap,
  23.         mktemp, mount, mv, nc, netmsg, netstat, nice, nslookup, ntpd, passwd,
  24.         pgrep, pidof, ping, ping6, pivot_root, poweroff, printf, ps, pwd,
  25.         readlink, reboot, reset, rm, rmdir, rmmod, route, sed, seq, sh, sleep,
  26.         sort, start-stop-daemon, strings, swapoff, swapon, switch_root, sync,
  27.         sysctl, syslogd, tail, tar, tee, telnet, telnetd, test, time, top,
  28.         touch, tr, traceroute, true, udhcpc, umount, uname, uniq, uptime,
  29.         vconfig, vi, watchdog, wc, wget, which, xargs, yes, zcat

  31. root@OpenWrt:/#
复制代码
回复

使用道具 举报

singing
发表于 2013-8-23 01:12:50 | 显示全部楼层
这样弄OPENWRT在SD卡上启动比较繁琐
回复 支持 反对

使用道具 举报

komoner0
发表于 2013-9-5 15:10:52 | 显示全部楼层
请问安装了OpenWRT在CB上，如何添加自己需要的东西呢？比如我想加一个可以实现文件转换的小程序，除了写这个程序之外，还需要怎样添加到OpenWRT上呢？
回复 支持 反对

使用道具 举报

tll
 楼主| 发表于 2013-9-6 22:40:35 | 显示全部楼层
komoner0 发表于 2013-9-5 15:10
请问安装了OpenWRT在CB上，如何添加自己需要的东西呢？比如我想加一个可以实现文件转换的小程序，除了写这 ...

ow里面有opkg命令能安装东西，但是sunxi目前不可用因为官网没这玩意。外部添加程序请用scp
回复 支持 反对

使用道具 举报

wake
发表于 2013-12-20 21:43:13 | 显示全部楼层
可否支持CB3？
回复 支持 反对

使用道具 举报

zpd1047
发表于 2013-12-21 14:51:26 | 显示全部楼层
好东西，先谢谢了，cb2，买卡准备刷
回复 支持 反对

使用道具 举报

tll
 楼主| 发表于 2014-1-16 13:25:51 | 显示全部楼层
zpd1047 发表于 2013-12-21 14:51
好东西，先谢谢了，cb2，买卡准备刷

cb2有内核问题，还是要编译
回复 支持 反对

使用道具 举报

hilongjw
发表于 2014-7-24 16:58:16 | 显示全部楼层
最近正想搞这个，谢谢楼主
回复 支持 反对

使用道具 举报

fengwufeiyang01
发表于 2014-11-23 14:58:28 | 显示全部楼层
下载包的速度很慢啊，动不动就中断了。版主能不能放一个编译好的镜像出来？
回复 支持 反对

使用道具 举报

a1036862671
发表于 2015-3-31 12:03:39 | 显示全部楼层
zpd1047 发表于 2013-12-21 14:51
好东西，先谢谢了，cb2，买卡准备刷

cb2怎么编译这玩意，装GCC失败
回复 支持 反对

使用道具 举报

返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|Archiver|手机版|粤ICP备13051116号|cubie.cc---深刻的嵌入式技术讨论社区

GMT+8, 2024-4-18 08:13 , Processed in 0.031237 second(s), 15 queries .

Powered by Discuz! X3.4

© 2001-2012 Comsenz Inc. | Style by Coxxs

返回顶部